Aggiusta le tue cose Community Store

Riparare la Apple Wireless Keyboard senza distruggerla

Passo precedente

Traduzione in corso passo 12

Torna alla Guida
Inglese
Italiano
Passo 12
Nessuna immagine
Closing it up

  • Once you're satisfied your keyboard is now fully working, turn it off, re-install the thin metal plate and use superglue to replace the welds and hold it down. Apply firm pressure while the glue cures so there are no gaps.

  • This will take a while, but it's worth doing properly because those welds were important! They stopped the entire keyboard from popping out when you press on a key. The superglue will suffice and with the added benefit of being easily removed if you need to re-enter the keyboard.

  • If the adhesive on the back of the plate is still in fairly good condition, you should be able to stick the white plastic cover back on. If not, use a little glue.

  • You can now re-install the grey plastic cover and every single key on the keyboard. To do this, apply pressure between two fingers to clip the keys back on, one on the underside. This will stop the glue from breaking.

  • That's it! Test it again to make sure it works. If it does you're clear to start using it again. Just be mindful that the structure has been compromised. Smashing your fists on the keys at any time will undo your work gluing it back together.

Richiudere

Dopo che hai controllato che la tastiera funzioni, spegnila, reinsalla la sottile piastra in metallo con della super colla al posto delle saldature e tienila schiacciata sulla tastiera. Fai una pressione costante in modo che non ci siano spazi.

Ci servirà un po', ma è meglio farlo correttamente in quanto queste saldature sono importanti! Evitano che l'intera tastiera si apra quando premi un tasto. La super colla sarà sufficiente con l'aggiunta di essere più facile da rimuovere se devi rismontare la tastiera.

Se l'adesivo sul retro della piastra è ancora in buone condizioni, dovresti poterla usare per incollare la copertura posteriore bianca. Altrimenti usa un po' di colla.

Puoi ora reinstallare la copertura in plastica grigia e tutti i tasti sulla tastiera. Per farlo, fai forza con due dita sul tasto ed uno sul retro per riagganciare i ganci. Questo eviterà che la colla si separi.

Ecco fatto! prova ancora per assicurarti che funzioni. Se è così, sei libero di tornare ad usarla. Ricordati che la struttura è stata compromessa. Sbatterci sopra i pugni annullerà il lavoro fato reincollando il tutto.

[title] Closing it up
-[* black] Once you're satisfied your keyboard is now fully working, turn it off, re-install the thin metal plate and use superglue to replace the welds and hold it down. Apply firm pressure so there are no gaps.
+[* black] Once you're satisfied your keyboard is now fully working, turn it off, re-install the thin metal plate and use superglue to replace the welds and hold it down. Apply firm pressure while the glue cures so there are no gaps.
[* black] This will take a while, but it's worth doing properly because those welds were important! They stopped the entire keyboard from popping out when you press on a key. The superglue will suffice and with the added benefit of being easily removed if you need to re-enter the keyboard.
[* black] If the adhesive on the back of the plate is still in fairly good condition, you should be able to stick the white plastic cover back on. If not, use a little glue.
[* black] You can now re-install the grey plastic cover and every single key on the keyboard. To do this, apply pressure between two fingers to clip the keys back on, one on the underside. This will stop the glue from breaking.
[* black] That's it! Test it again to make sure it works. If it does you're clear to start using it again. Just be mindful that the structure has been compromised. Smashing your fists on the keys at any time will undo your work gluing it back together.

I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.